# AIST and DOWA's lab powder coater deposits zinc on alumina with over 100 times sputtering's energy efficiency

- Published: 2026-11-19 10:12 UTC
- Section: Machines & Making › Manufacturing
- Tags: powder coating apparatus, vacuum evaporation of powders, downward vapor source, dome-shaped crucible, zinc film on alumina, sputtering comparison, metal-coated powder, AIST DOWA
- URL: https://realtech.media/news/rt-42a12aea6fa8576b4d3f9ca4_aist_and_dowa/

**AIST and DOWA built a lab-scale evaporation source that sends metal vapor downward onto stirred powder. In a zinc-on-alumina test it far outpaced sputtering in deposition per unit of energy.**

![AIST and DOWA's lab powder coater deposits zinc on alumina with over 100 times sputtering's energy efficiency](https://realtech.media/media/2026/11/d76a933a7970f317.webp)
*xenospectrum.com*

The National Institute of Advanced Industrial Science and Technology (AIST) and DOWA Holdings announced on 18 November 2026 a coating apparatus that forms metal films on powder surfaces by fast vacuum evaporation, according to xenospectrum.com [1]. In a test with zinc on alumina powder, the device deposited 14.8 g/h of zinc, and its deposition per unit of energy was about 113 times that of a sputtering setup [1]. The results come from laboratory material-processing tests; no peer-reviewed paper or preprint on the device has been found [1].

## Downward vapor source for powders

Powders for battery materials, electronic components and catalysts gain corrosion resistance, conductivity or thermal conductivity from a thin metal film [1]. The powder must be stirred in an open container, so the metal has to be supplied from above [1]. Sputtering can do this but deposits slowly, while conventional evaporation holds molten metal in a crucible and emits vapor mostly upward [1].

The team designed a dome-shaped crucible with an opening only at the bottom. When the whole crucible is heated in high vacuum, vapor rises from the molten metal, reaches the hot inner wall of the dome without condensing, changes direction and exits downward through the opening, AIST explained [1]. Below it, a rotating disc-shaped container with a stirring fixture keeps changing the position and orientation of the particles [1].

## Test conditions and results

The test used 200 g of alumina powder (median particle size 15.4 μm, specific surface area 2,248.36 cm²/g) and 7.5 g of zinc pellets [1]. After the chamber was evacuated to 2×10⁻³ Pa or below, the source was heated to 750 ℃ over 25 minutes and held for 5 minutes [1]. Scanning electron microscopy and energy-dispersive X-ray analysis showed a zinc layer around the alumina particles; the mean zinc content was 3.2% by mass, and the team estimates the mean film thickness at 20.6 nm [1].

In the comparison, average power was estimated at about 680 W for the new device and about 780 W for sputtering with a 2-inch zinc target [1]. Deposition was 14.8 g/h against 0.15 g/h, a value for sputtering corrected for setup differences; the measured value was 0.0376 g/h, multiplied by four [1]. Per unit of energy, the figures were 2.18×10⁻² g/Wh and 1.93×10⁻⁴ g/Wh [1]. The comparison applies to the equipment and conditions used, not to all sputtering systems [1].

The published data do not include repeat counts, error ranges, per-particle thickness distribution, or measurements of corrosion resistance, conductivity or other functional gains [1]. Metals that evaporate less readily will need higher temperatures and a suitable crucible material [1]. The developers plan coating without exposing the powder to air and work with chemically reactive powders [1]. Details are due at the Society of Powder Technology, Japan autumn meeting on 24–25 November [1].

## Sources

1. [xenospectrum.com](https://xenospectrum.com/aist-dowa-downward-vapor-powder-coating)

---

Source: RealTech, realtech.media — https://realtech.media/news/rt-42a12aea6fa8576b4d3f9ca4_aist_and_dowa/
